Black 8 Channel DVR Spezifikationen PDF herunterladen (Seite 9)

The easiest way to access your DVR remotely is via an Internet browser. These

instructions will detail how to access the DVR via Microsoft Internet Explorer

. This

section assumes that you’ve already con gured the DVR and your network to operate

properly. Remotely accessing the DVR via Internet Explorer (IE) is a great way to test

if your network is functioning as it should.

At the time of writing, the DVR supports up to

3 users accessing the DVR remotely at a time.

Note: You may have to alter and con gure the ActiveX controls in IE to allow

unrestricted access to the DVR. Access might be slowed or blocked completely by

IE’s built-in security functions. The instructions on how to do this are covered on the

next page.

To access the DVR remotely via Internet Explorer:

1. Open an Internet Explorer window. If you do not have Internet Explorer you can

download it from the Microsoft website (www.microsoft.com).

2. In the address bar type “http://” followed by your public IP address, a

colon then your web port. For example, if your web port is “85” and

your public IP address is “210.9.10.115”, then you’ll need to enter the

information, shown on the image, immediately below these words

You will now see a login window. Here, enter your password. If no password is

set, leave this dialog box blank.

3. You should now have access to the DVR.

http://210.9.10.115:85

Remote Access via Internet Explorer

Layout of the Rear Panel

1) CH1 ~ CH8 (Video Inputs): These

are the eight camera inputs, labelled as

per their channel in the DVR’s interface.

Thus, plug the camera you want to be

associated with Channel 1 into the port

marked CH1 and so on.

2) Video Outputs: This sends a

composite video signal out of the DVR.

Each of the two ports can be connected

to separate monitors. The output

marked MAIN will show the main

DVR interface (all channels accessible

plus menus, unless you’ve conﬁ gured

the DVR to use the VGA as the main

output).

3) Audio Inputs (CH1 ~ CH4): Four

labelled audio inputs. These will accept

standard line-level signals (<1V) and

can be assigned to channels later.

4) Audio Output: Two mono audio

output channels. These output a

standard ‘line-level’ signal, and can

easily be connected to the audio inputs

on a television or stand-alone audio

device.

5) VGA Output: For connection to a

VGA monitor. This will display the same

image as the MAIN video output at a

selectable resolution between 800 x

600, to a maximum of 1440 x 900.

6 Above) USB Mouse Port: For

connecting the included USB mouse

(other standard USB mice will also

work). This port will not accept a USB

ﬂ ash drive – this port will work with a

mouse only.

6 Below) USB Backup Port: For

connecting a USB ﬂ ash drive for the

purposes of backing up footage.

7) RS485 Connections: This is the serial

communication port, used primarily to

connect PTZ (pan, tilt, zoom) devices.

8) Power Connection: For supplying

power to the DVR. Use only the supplied

power adaptor, and do NOT change or

modify it in any way. Modiﬁ cations to

your power supply radically increases

the risk of electrocution or ﬁ re, and will

immediately void your warranty.

9) LAN Port: To connect an Ethernet

cable, allowing the DVR to be connected

to a local area network. This network,

in turn, can be used to give the DVR a

connection to the Internet.

)

CH1 ~ CH8

(

Video In

uts

)

: These selectable resolution between 800 x

8579 6

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 37 38

Kommentare zu diesen Handbüchern

Keine Kommentare

Black 8 Channel DVR Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale Videorecorder (DVR) Black 8 Channel DVR